Solutions/Network Security Monitoring

Network Security Monitoring Software Built on Full Packet Capture

SentryWire is network security monitoring software that works from complete packet data rather than logs or flow summaries. SOC teams in federal, critical infrastructure, and regulated enterprise networks use it to validate alerts, find what detection tools missed, and investigate months back, from one record of the traffic itself. New to the discipline? Start with what network security monitoring is.

Illustrative example · a SOC without the packets

  • IDS alert: possible C2 beacon from an internal host. SIEM shows the connection. Nothing else.
  • Can't validate. Flow data has bytes and timestamps. No payload, no session.
  • Can't scope. The NDR look-back window covers a few days. First contact was weeks ago.
  • Can't prove. Auditor asks what left the network. The answer is an estimate.
  • With SentryWire: alert → packets, weeks back. Every session, every lateral hop, and the exfiltration volume, reconstructed from the traffic itself.

The Problem

Most Network Security Monitoring Software Monitors Reports About Traffic, Not the Traffic

SIEM, NDR, and IDS platforms each see a slice. None of them keeps the thing every investigation eventually needs.

Can I confirm this alert?

Logs and flow records say a connection happened. They cannot show what moved inside it, so an alert is either trusted or dismissed on faith.

SentryWire: pivot to the packets behind the alert.

How far back does this go?

Breaches are often discovered months after entry. Detection tools may or may not keep a short packet buffer around alerts, so the entry point and the first lateral hop are often already gone.

SentryWire: months to years of retained traffic.

What can I show an auditor?

OMB M-21-31, NERC-CIP, and SEC 17a-4 expect verifiable network evidence. A log summary is not evidence of what left the network.

SentryWire: packet-level proof, not estimates.

How It Works

Packet-Level Network Security Monitoring, Step by Step

SentryWire sits under your detection stack as the evidence layer. Each step feeds the next.

Capture everything

Passive, lossless capture from SPAN ports or TAPs across every monitored segment, at 10 Gbps to 1 Tbps, where legacy capture and IDS platforms drop packets.

Detect continuously

Integrated Suricata runs on live traffic with alerts mapped to MITRE ATT&CK. Your SIEM, Zeek, and NDR alerts arrive alongside it.

Validate against the packets

Any alert pivots straight to the sessions it was raised on. Confirm, scope, or dismiss in minutes.

Investigate backward

Search months of retained traffic. Run new signatures against old packets. Reconstruct sessions and carve files.

Hand off evidence

Export PCAPs to Splunk, Elastic, or the case file. The same record satisfies the auditor and the incident report.

Walk Through It on Your Traffic

At a Glance

How Network Security Monitoring Software Compares

Most NSM software monitors what other systems report. Packet-level NSM monitors the traffic itself.

CapabilitySIEM-Based NSMNDR / XDRIDS (Suricata, Zeek)Packet-Level NSM (SentryWire)
Monitors fromLogs and eventsBehavioral modelsSignatures on live trafficComplete packets
Retains raw packetsNoHours to days, around alertsAlerts onlyMonths to years
Validates an alert against trafficNoWithin its bufferWithin its bufferYes, full retention window
Finds threats missed at the timeNoNoNoYes, search back
Reconstructs sessions and filesNoNoNoYes
Audit-grade evidenceLogsAlertsAlertsPackets
Role in the stackCorrelationDetectionDetectionEvidence layer under all three

Built On

Runs on the SentryWire Full Packet Capture Appliance

The monitoring software and the capture platform are one system. Platform specs, architecture, and deployment details live on the full packet capture appliance page.

OMB M-21-31 CDM NERC-CIP SOC 2 SEC 17a-4
1 Mbps to 1 Tbps+Lossless line-rate capture
Months to yearsRetention on commodity storage
25 to 40% lowerTCO vs legacy packet capture

FAQ

Network Security Monitoring Software FAQs

What should network security monitoring software include?

Network security monitoring software should capture traffic at the packet level rather than relying on logs, validate alerts from your SIEM and IDS against the raw traffic, retain data long enough to investigate threats discovered months after entry, integrate with the detection tools you already run, and produce evidence that holds up in a compliance audit. Tools that only correlate logs or keep a few days of packets around alerts fail at least one of those tests.

How does network security monitoring differ from network troubleshooting?

Network troubleshooting looks for performance problems: latency, congestion, and outages. Network security monitoring looks for adversaries: lateral movement, command-and-control, and exfiltration. SentryWire is built for the second job; performance metrics are a byproduct of the packet data, not the purpose.

Why is full packet capture important for security monitoring?

Because logs and flow records summarize what happened, and summaries cannot be re-examined. Full packet capture preserves the traffic itself, so an alert can be validated, an intrusion reconstructed, and a threat missed at the time found later with newer signatures.

How does SentryWire support incident response and forensic investigations?

Investigators pivot from an alert to the sessions behind it, reconstruct sessions and carve files from the capture store, and trace the intrusion across the full retention window instead of inferring it from logs.

Can network security monitoring work with encrypted traffic?

Yes. Even without decryption, packet-level monitoring sees connection patterns, TLS fingerprints such as JA3, certificate details, timing, and volume, which is how C2 beaconing and exfiltration are identified inside encrypted sessions.

Is SentryWire suitable for ICS and OT network security monitoring?

Yes. SentryWire monitors passively from SPAN ports or network TAPs, so it never touches industrial endpoints or injects traffic, which makes it suitable for ICS and OT environments.

What compliance frameworks does network security monitoring need to support?

In federal and regulated environments, the common ones are OMB M-21-31, CDM, NERC-CIP, SOC 2, and SEC 17a-4. All of them expect verifiable, retained network evidence, which packet-level monitoring provides directly.

How does network security monitoring differ from NDR?

NDR detects threats from behavioral models and raises alerts, usually keeping a short packet buffer around each one. Packet-level NSM keeps all the traffic, so NDR alerts can be validated and investigated against the full record. The two complement each other.

What is the difference between network security monitoring and SIEM?

A SIEM correlates logs and events from other systems. It never sees the packets. Packet-level network security monitoring is the evidence layer a SIEM pivots into when an alert needs to be confirmed or scoped.

How does network security monitoring differ from IDS and IPS?

IDS and IPS match live traffic against signatures and act on it in real time. They do not retain the traffic. SentryWire runs Suricata on live and stored packets, and keeps the packets, so detections can be validated and new signatures run against historical traffic.

Demo

See Packet-Level Monitoring on Your Traffic

Free Demo

A tailored walkthrough covering packet-level monitoring, alert validation, retention, and integration with Splunk, Elastic, and your existing SIEM, on traffic patterns that look like yours.

  • Free, no obligation
  • Walkthrough tailored to your environment
  • Same-day response from a SentryWire engineer

Works with your stack

Splunk Elastic Palo Alto Networks IBM Security Red Hat

Network security monitoring software that keeps the packets, not just the logs.

Request an NSM Demo